simpleanalytics

CDR Guidelines – Engineering Associate Career Episode Sample

Having Trouble Writing your Career Episode Report ?

Get in Touch with Our Writers to get the Help you Need and Avoid Possible Rejection!

Or talk to our writers at +61 481 614 316 / +61 483 968 416

    Get Free Consultation




    Career Episode Report Example for Engineering Associate

    A competency demonstration report (CDR) requires migrant engineers applying to Engineers Australia to write three career episode reports (CERs). Career Episode Report for Engineers Australia gives detailed information on technical and other skills an engineer applied to the project described. You must demonstrate your professional competencies in your career episodes. Here is a writing style for a Career Episode Report Example for Engineering Associate.

    INTRODUCTION

    CE 1.1

    I have demonstrated about my project titled “Simple Timer Switching Circuit” as a requirement for this career episode. I have done this project as a requirement for my Diploma in Electrical Engineering and submitted to the Department of Electrical Engineering of XXX (University Name and location). This project was started on… and completed on… under the supervision and direction of my project supervisor …………

    BACKGROUND

    CE 1.2

    The touch ON and OFF switches circuit is the simple circuit that works with the use of 555 IC timer device. The IC timer has 8 pins which are connected to the touch plates as per the default properties of the 555 Timer IC pins. For the simplicity of the functioning of the device, this simple touch circuit can be used to turn ON and OFF any devices by the simple touch on the touch plates. When we touch on the touch ON plate of the circuit, the device gets activated, and when we touch on the touch OFF plate of the circuit, the device gets deactivated.

    CE 1.3

    The major objectives associated with the project are:

    To design a simple touch ON and OFF circuit with the use of 555 Timer IC.

    To analyze the working mechanism of the touch circuit with the copper touch plates.

    CE 1.4

    This project was an individual academic project, and thus there was no involvement of any other teammates for this project. However, I took the guidance and supervision of the project supervisor for the project. The organizational with the illustration of my position in the project is shown below:

    CE-Eng-Manager1

    CE 1.5

    I was the sole individual responsible for the completion of the project. The major responsibilities that I performed for this project were:

    Accumulate the necessary information for the completion of this project through the literature review of the other projects and reference books

    Make the circuit diagram of the touch circuit with the use of 555 timer IC

    Select the necessary components for the circuit design

    Select the copper boards as the touch plates required as the touch sensor for the device operation

    Connect all the components as per the default pin configuration of 555 Timer IC

    Supply the power to the circuit and analyzed the working mechanism with the ON and OFF of the touch circuit

    Submit the progress report of the project to the supervisor for the review

    PERSONAL ENGINEERING ACTIVITY

    CE 1.6

    This project was an individual academic project. I was the single individual responsible for the completion of this project. Thus, before initiating the designing task of the project, I referred the reference books from the library and some videos on the internet sources regarding the project ideas and information. Then, I organized the gained information in a systematic way to make the project schedule and carried out the real task of the project.

    CE 1.7

    Firstly, I made the circuit diagram of the required touch on and off switch circuit. The circuit diagram is below: (ANZSCO code 233311 task 2)

    CE-Eng-Associate2

    CE 1.8

    After the completion of the required design of the switch circuit using touch plates, I analyzed and selected the required components for the project. The selected components are listed below: (ANZSCO code 233311 task 2)

    555 Timer IC

    5V relay module

    2 MΩ resistor

    Bulb

    Breadboard

    CE 1.9

    As the components were selected, the next task was the making of the touch plates for the project as they were the vital part of the project design. I used two small pieces of copper-clad boards of required dimension. Then, I made the groove in the middle of the used copper board without breaking it completely. I did this so that there will be two halves on the board required for the project. (ANZSCO code 233311 tasks 3)

    CE 1.10

    The next phase of the project was the task of the circuit design of the touch on and off switch circuit. For this, I connected the GND, VCC and RST pins of the used 555 Timer IC which are the pins 1, 8 and 4 respectively of timer IC to the GND and 5V respectively. Similarly, high MΩ resistor was connected to pin 2 and low MΩ resistor to the pin 6 of the timer IC. In the remaining pins 2 and 6, I connected two touch plates as per the circuit diagram. I connected the touch plates in such a way that one end of touch ON plate is connected to pin 2 and another end to GND. Likewise, one end of touch OFF plate is connected to pin 6 and another end to a 5V source. (ANZSCO code 233311 tasks 3)

    CE 1.11

    After the completion of the circuit connection with the pins of the timer IC, I applied the power supply to the circuit and observed the working of the project. The basic principle is that I had to touch on the ON plate for turning on the device and touch on the OFF plate for turning off the device. Firstly, I touched on the ON plate. As a result, the voltage at pin 2 of IC became low, and thus the pin 3 became high. Then, the transistor will turn on as this pin 3 is connected to the relay module used in the circuit. Finally, the device gets switched ON.

    Next, I touched on the OFF plate of the circuit, then pin 6 of the timer IC was supplied with 5V for some duration and thus, the pin 3 which is the output pin became low. As a result, the connected transistor gets turned off and thus the relay of the circuit. Finally, the device gets switched OFF. (ANZSCO code 233311 task 5)

    CE 1.12

    I observed that the device worked as a flip-flop device. When the touch ON plate is pressed, the relay gets activated and thus the device. When the touch OFF plate is pressed, the relay gets deactivated and thus the device.

    CE 1.12

    I observed that the device worked as a flip-flop device. When the touch ON plate is pressed, the relay gets activated and thus the device. When the touch OFF plate is pressed, the relay gets deactivated and thus the device.

    CE 1.13

    Initially, during the connection of the pins of 555 Timer IC with the components and the touch plates, I had connected the pins with the wrong configuration so, the circuit didn’t function. For easing this issue, I referred the datasheet for the pin configuration and connected the pins with proper configuration. (ANZSCO code 233311 task 4)

    Another problem that I faced during the circuit operation was that sometimes the circuit triggered itself without touching the touch plates. To solve this issue, I reduced the sensitivity of the circuit by the reduction of the resistance value of the resistor connected to the touch on the plate.

    CE 1.14

    I used two small pieces of copper clad boards as the requirement for touch plates used in the circuit. (ANZSCO code 233311 task 3)

    CE 1.15

    This project about the design of the simple touch ON and OFF circuit with the use of 555 Timer IC was done as an individual project. I performed all the tasks associated with the project and ensured that the project was completed within a limited time. For the difficulties I faced on the project, I consulted with my project supervisor. His effective guidance and suggestions throughout the project were vital for my project completion with the achievement of the desired results. I also submitted the progress report of the project to the supervisor on a weekly basis. I maintained effective verbal and written communication with the supervisor throughout the entire project. (ANZSCO code 233311 task 5)

    CE 1.16

    I ensured that the project work was carried out as per the associated norms and ethics of the project. I followed the regulations of the Electrical Engineering Department and the university effectively while performing this project task. During the interaction with the supervisor, I used to present myself in an organized and disciplined manner and followed his guidance with full respect. Likewise, I didn’t dispute with the supervisor or any persons while performing the project and carried out the project in a peaceful and safe environment. I followed the datasheets of 555 Timer IC while performing the pin configuration on the circuit. The components used in the circuit were standard components that were approved to use in the country. (ANZSCO code 233311 task 4).

    SUMMARY

    CE 1.17

    Finally, the project about the design of the simple touch ON and OFF switches circuit with the use of 555 Timer IC was complete within the limited time with my dedication and guidance of the supervisor. This project made use of the relay module and copper plates as the touch plates required for the project. This circuit works as per the basic functionality of the configuration of the pins of 555 Timer IC. The proposed design circuit can be used to turn ON and OFF any device by simply touching the touch plates. Overall, this project is simple to design and economical as only a few components are used in the design of the circuit.

    Other Career Episode Report Samples

    Make Sure your Report gets Accepted by the ACS

    Instead of wasting your time and money with incompetent agencies, contact us for your guaranteed success. Our writers will make sure the results are refined, proofread, and plagiarism free. We are giving Free Consultation for our clients.

    Pricing of Complete CDR Report Writing

    We provide our complete CDR Writing service on the basis of your urgency level and prices respectively. There are currently three types of service that you can purchase which are shown below.

    15 days plan
    AUD
    799
    • 3 Career Episodes
    • Summary Statement
    • Plagiarism Check
    • Correction Limit (3 times)
    • Speak with the Writer
    • PR procedure guidance
    • Full Refund
    10 days plan
    AUD
    999
    • 3 Career Episodes
    • Summary Statement
    • Plagiarism Check
    • Correction Limit (6 times)
    • Speak with the Writer
    • PR procedure guidance
    • Full Refund
    7 days plan
    AUD
    1299
    • 3 Career Episodes
    • Summary Statement
    • Plagiarism Check
    • Correction Limit
    • Speak with the Writer
    • PR procedure guidance
    • Full Refund
    Royal Package
    AUD
    2999
    • 3 Career Episodes
    • Summary Statement
    • Plagiarism Check
    • Correction Limit
    • Speak with the Writer
    • PR procedure guidance
    • Full Refund

    1000s of Satisfied Customers

    Our Services receive great response and guarantee Success. Few client feedbacks are shown below.

    Our Hundreds of Clients are getting Successful Approval, When will you?

    Our primary goal is to ensure our clients' successful approval through well-documented CDR reports that match EA standards for migrants. CDR Writers Australia provides quality CDR and ACS skill assessment services, aiming for 100% skill assessment success.

    Best Prices

    Best Prices

    We provide most reasonable price while maintaining the superior report quality.
    On-time Delivery

    On-time Delivery

    We commit to our deadlines very seriously and believe in customer satisfaction.
    Report Structure

    Report Structure

    Following the guidelines is our top priority for maximum positive results.
    100% Original Content

    100% Original Content

    Our experienced engineers have the skills to provide original and unique content quality.

    Feeling Curious? Get Your CDR Approved—Call Us Now! +61 481 614 316 / +61 483 968 416

    We are here to answer all your queries and provide you the best service. Feel free to contact our writers for your concerns.